<ul><li>Creates white water-based coating</li><li>Used for protection of walls and the door of a spray booth against overspray</li><li>White, reflective surface for maximum light in the room</li><li>Easy application by a roller or brush</li><li>Possibility of covering with a new layer in the case of contamination of peelable coating</li><li>Easily peelable</li><li>Packing: 30 kg</li></ul>

large_ewac_10_26.jpg

medium_ewac_10_26.jpg

small_ewac_10_26.jpg

thumbnail_ewac_10_26.jpg

ewac_10_26.jpg

thumbnail_snímací lak.jpg

snímací lak.jpg

We offer peelable coatings which protect the spray booth against overspray, impurities and dust. Our range of products includes coatings for protection of walls, windows, doors and lamps. Coatings are applied by spray gun or by using a roller and brush. They are either transparent, white or creamy colour. Coatings are easily removed from surfaces.

We sell by cans 25 – 30 kg /l. 

#### Peelable coating white AZ1 – 700

- Creates white water-based coating
- Used for protection of walls and the door of a spray booth against overspray
- White, reflective surface for maximum light in the room
- Easy application by a roller or brush
- Possibility of covering with a new layer in the case of contamination of peelable coating
- Easily peelable
- Packing: 30 kg 
 
#### Peelable coating transparent AZ0 – 700

- Creates transparent coating
- Water-based coating
- Used for protection of windows and lamps of the spray booth against overspray
- Transparent and light-permeable
- Easy application by using a roller or brush
- Easily peelable
- Packing: 30 kg  

#### BARRIER GEL

- Transparent, water-based tacky coating
- Fine gel form
- Suitable for spray booths with strong contamination
- Used for protection of walls and doors against overspray impurities and dust
- Easy application by using a brush or spray guns
- Easily washable with (warm) water
- Packing: 30 kg

#### Propeel HD

- Creates cream-like coating
- Solvent-based coating
- Used for protection of floors in spray booths against overspray
- Mechanically and chemically resistant
- Easy application with a roller or brush
- Possibility to remove it and apply it again on the most exposed parts
- Easy to peel
- Packing 25 l 
 
#### TACKY coating

- Water-based coating
- Used for wall protection against overspray
- Easy application with a roller, brush or spray gun
- Usable up to 85°C
- Temporary protection of walls, windows, lamps against overspray in spray booths
- Reduces dust rate in the spray booth
- Easily washed down with warm water 

Peelable coatings and protective paints

Peelable coating white AZ1 – 700

<p>The base of the filter insert is a filter medium in the form of special filtration papers made of glass sub-micron fibres.&nbsp;</p><p>This filtration paper is folded into a stable folded thread, whose optimal number and height of folds corresponds with the operating point of the filter and ensures the long lifespan of the filter insert. The paper is separated by hot-melt beads.&nbsp;</p><p>Filter thread is hermetically fixed to the frame made of the anodized aluminium profile, which along with endless sealing of the PUR foam guarantees high-quality filter inserts in the mounting cabinets. This filter structure is a base for compliance with high requirements regarding air purity. Filter inserts U 15 are normally delivered with a protective grille on the outlet side.&nbsp;</p><h3>Field of use</h3><ul><li>Medicine</li><li>Microbiology</li><li>Chemical industry</li><li>Pharmaceutical industry</li><li>Food-processing industry</li><li>Electrical engineering industry</li></ul><h3>Examples of use</h3><p>This highly efficient filter insert with high arrestance against all types of aerosols is used as the end filter of multi-level filtration of air-conditioning or ventilation equipment, for purification of supplied and outlet air in technologically demanding processes and for purification of air from health-harmful dust, viruses and bacteria in hospital facilities.&nbsp;</p><h3>Advantages of design</h3><ul><li>High mechanical stability</li><li>Optimal structure of the folded thread</li><li>Steady output airflow velocity</li><li>Protective grille on the output side</li></ul><h3>Delivery</h3><ul><li>Filter inserts, various sizes</li><li>Installation depth: 69, 78, 90, 117 mm</li><li>Frame material: aluminium</li><li>Sealing type: foamed PUR, flat rubber, U-profile</li><li>Sealing position: at the inlet and outlet</li></ul>

large_20210114_ewac_016.jpg

medium_20210114_ewac_016.jpg

small_20210114_ewac_016.jpg

thumbnail_20210114_ewac_016.jpg

20210114_ewac_016.jpg

### MICROPUR

The base of the filter insert is the filter medium in the form of special filtration papers made of glass sub-micron fibres.

This filtration paper is folded into a stable thread, whose optimal number and height of folds with respect to the operating point of the filter ensures the required filter class and long lifespan of the filter insert. The paper is separated by hot-melt beads.

Filtration thread is hermetically sealed into a stable, torsion-resistant filter frame, which along with the endless sealing made of PUR foam, guarantees quality-sealing of the filter insert in mounting cabinets. This filter structure is the base for compliance with high requirements for air purity. The basic frame material is MDDF. On request, the frame filter can be made also of zinc-plated and steel, stainless steel or aluminium metal sheets.

#### Field of use

- Medicine
- Microbiology 
- Chemical industry 
- Pharmaceutical industry 
- Food-processing industry 
- Electrical engineering industry 
- Nuclear technology

#### Examples of use

This highly efficient filter insert with higher arrestance against all types of aerosols is used as an end filter of multi-level filtration in air-conditioning and ventilation devices, for cleaning of inlet and outlet air in technologically demanding processes and for purification of air from harmful dust, viruses, and bacteria in hospital facilities.

#### Advantages of design

- High mechanical stability 
- Optimal structure of folded thread 
- Steady outlet airflow velocity
- Various types of frame and sealing materials

#### Delivery

- Standard installation depth: 46, 54, 69, 78, 150, 292 mm
- Frame material: aluminium, stainless steel, MDF, plywood
- Type of sealing: foamed PUR, flat rubber, U-profile
- Sealing position: inlet, outlet 

### MACROPUR

The base of the filter insert is the filtration medium in the form of special filtration papers made of glass sub-micron fibres.

This filtration paper is folded into a stable folded thread, whose optimal number and height of folds is in compliance with the operating point of the filter and ensures the required filter class and long lifespan of the filter insert. The paper is separated by hot melt (MACROPUR) beads or with separators made from aluminium foil (MACROPUR).

Filter thread is hermetically sealed into a stable, torsion-resistant filter frame and along with endless sealing from PUR foam it guarantees a high-quality sealing of the filter insert in the mounting cabinets. This filter structure is the base for compliance with high requirements for air purity. The basic frame is made of MDF. On request, it is also possible to make the filter frame from zinc-plated, stainless or aluminium metal sheets. 

#### Field of use

Medicine
Microbiology
Chemical industry
Pharmaceutical industry  
Food-processing industry 
Electrical engineering industry
Nuclear technology

#### Examples of use

This highly efficient filter insert with high arrestance of all types of aerosols is used as the end filter of multi-level filtration in air-conditioning and ventilation equipment, for purifying of inlets and outlets of air in technologically demanding processes and purification of air from health-harmful dust, viruses, and bacteria in hospital facilities.

#### Advantages of design

- High mechanical stability
- Optimal structure of the thread 
- Steady output airflow velocity
- Various types of frame and sealing

#### Delivery

- Filter inserts, various sizes.
- Paper separation: hot-melt beads, aluminium foil 

### ABSOPUR

The base of the filter insert is a filter medium in the form of special filtration papers made of glass sub-micron fibres.

This filtration paper is folded into a stable thread, whose optimal number of folds and height of folds corresponds with the operating point of the filter. This also ensures the required filter class and long lifespan of the filter insert. The paper is separated with hot melt beads.

Filtration thread is hermetically fixed into the anodized aluminium profile and, along with the endless sealing from foam PUR, guarantees quality sealing of the filter insert in mounting cabinets. This filter design is the base for compliance with high requirements regarding air purity. Filter inserts H14 are normally delivered with a protective grille on the outlet side. 

#### Field of use

- Medicine 
- Microbiology 
- Chemical industry
- Pharmaceutical industry 
- Food-processing industry
- Electrical engineering industry

#### Examples of use    
     
This highly efficient filter insert with high arrestance against all types of aerosols is used as an end filter in multi-level filtration of air-conditioning or ventilation equipment to purify supplied and released air in technologically demanding processes and for purification of air from health-harmful dust, viruses, and bacteria in hospital facilities.

#### Advantages of design

- High mechanical stability
- Optimal design of the thread
- Steady output airflow velocity 
- Protective grille on the outlet side

#### Delivery

- Filter inserts, various sizes.
- Installation depth: 69, 78, 90, 117
- Frame material: aluminium
- Sealing type: aluminium, foamed PUR, flat rubber, U-profile
- Sealing position: at the inlet and outlet

### ULTRAPUR

The base of the filter insert is a filter medium in the form of special filtration papers made of glass sub-micron fibres.

This filtration paper is folded into a stable folded thread, whose optimal number and height of folds corresponds with the operating point of the filter and ensures the long lifespan of the filter insert. The paper is separated by hot-melt beads.

Filter thread is hermetically fixed to the frame made of the anodized aluminium profile, which along with endless sealing of the PUR foam guarantees high-quality filter inserts in the mounting cabinets. This filter structure is a base for compliance with high requirements regarding air purity. Filter inserts U 15 are normally delivered with a protective grille on the outlet side.

#### Field of use

- Medicine 
- Microbiology 
- Chemical industry 
- Pharmaceutical industry 
- Food-processing industry 
- Electrical engineering industry

#### Examples of use

This highly efficient filter insert with high arrestance against all types of aerosols is used as the end filter of multi-level filtration of air-conditioning or ventilation equipment, for purification of supplied and outlet air in technologically demanding processes and for purification of air from health-harmful dust, viruses and bacteria in hospital facilities.

#### Advantages of design

- High mechanical stability 
- Optimal structure of the folded thread 
- Steady output airflow velocity 
- Protective grille on the output side

#### Delivery

- Filter inserts, various sizes
- Installation depth: 69, 78, 90, 117 mm
- Frame material: aluminium
- Sealing type: foamed PUR, flat rubber, U-profile
- Sealing position: at the inlet and outlet

HEPA filters

Filter class [EN 1822]

Initial pressure drop [Pa]

End pressure drop [Pa]

Arrestance [%]

Max. operating temperature [°C]

Max. relative humidity [%]

Frame material

Filter medium

ULTRAPUR

<ul><li>Suitable for the automotive, plastic and wood-processing industries</li><li>Intended for cleaning and degreasing of metal, plastic and wooden surfaces before painting</li><li>Applied with izopropylalcohol</li><li>Material: 100 % polyester 190 g/m²</li><li>Size: 40 x 40 cm</li><li>Colour: white</li><li>Reusable</li><li>Antistatic rag</li><li>Packing: 1 kg (29 pc)</li></ul>

large_ewac_07_22.png

medium_ewac_07_22.png

small_ewac_07_22.png

thumbnail_ewac_07_22.png

ewac_07_22.png

large_shutterstock_150980831_mensi.jpg

medium_shutterstock_150980831_mensi.jpg

small_shutterstock_150980831_mensi.jpg

thumbnail_shutterstock_150980831_mensi.jpg

shutterstock_150980831_mensi.jpg

<p>We offer tacky and non-tacky antistatic cleaning industrial rags for wiping impurities from metal, plastic and wooden surfaces. Tacky rags are nonwoven impregnated fabrics, which capture dust particles, fibres and impurities from products just before painting. Manufacturers of cars, plastics and engineering products and electronics use these rags not only before painting, but also for maintenance of cleanrooms and wiping away of dust and other residues from moulds. Non-tacky rags, made of nonwoven fabric or polyester are intended for removal of grease, dirt and solvents from surfaces before their painting. Some are applied by using polypropylalcohol. Rags – T-shirts in boxes – are intended for universal cleaning of various surfaces.&nbsp;</p>

Industrial rags

Cleaning rag Cleanbez 08

<p>Andreae Starter composed of two layers of sulphate cardboard. Layers are perforated, folded and glued together.&nbsp;</p><p><strong>Holding capacity</strong>: up to 18 kg/m<sup>2</sup>*&nbsp;</p><p><strong>Filtration efficiency</strong>: up to 98.1 %*&nbsp;</p><h4>Optimum conditions of use:&nbsp;</h4><ul><li>Recommended air velocity: 0.25 - 1 m/s</li><li>Pressure loss: 0.25 m/s - 8 Pa, 0.5 m/s - 20 Pa, 0.75 m/s - 30 Pa, 1 m/s - 40 Pa</li><li>Maximum recommended pressure loss: 128 Pa - 256 Pa Delivery: size 10 m2 x 100 or 75 cm</li></ul>

small_1. Andreae Original Filter.png

thumbnail_1. Andreae Original Filter.png

1. Andreae Original Filter.png

large_ewac_filtry_011.jpg

medium_ewac_filtry_011.jpg

small_ewac_filtry_011.jpg

thumbnail_ewac_filtry_011.jpg

ewac_filtry_011.jpg

Andreae ﬁlters are composed of two folded, solid cardboards pieces which are glued to each other in bends. Openings on the front side are located asymmetrically against the openings in the rear wall. When the air goes through the filter, the airflow is changed in all axes.

In the rear wall, created by deeper bends in the V-shape, pockets are created to capture separated liquid particles.

### Principle

The air flow saturated with liquid particles, e.g. paints, is accelerated in the flow through the filter and multiply changes its direction. Particles heavier than air are separated from this stream by inertia. The air escapes through the outlet openings of the filter, while particles of paint are accumulated in the capturing chambers.

### Use

By using inertia, Andreae filters capture very efficiently aerosol cloud, which is created by the spraying of all types of liquid paints and lacquers, binding agents, adhesives, epoxide resins, solvents, asphalt, gels, tar, Teflon, polyurethane, vinyl, oils, grease, glaze, etc. Generally said, filters can be used everywhere where it is necessary to remove liquid particles from blowing foggy air. Andreae filters can be used independently or as a prefilter in multi-level filtration systems.

### Advantages

- Accumulation of paint outside the airflow slows down the increase in differences in pressures and air velocity. Lifespan of Andreae filters is 3-5 times longer than that of flat, fleece filters.
- Filters show high stability in the air stream. The front V-shape wall prevents the reflection of overspray. The employee remains in a clean environment and the air stream around the sprayed objects is stable.
- The folded structure of filters is very strong, it resists suction of ventilation and does not collapse even when it is relatively full.
- Filters with easy and quick exchange. They reduce operating costs for maintenance of spray booths. 

### Filter Andreae Original

Basic filter, used as a prefilter in multi-level filtration systems, where it captures the largest part of liquid particles of paint and protects the following level of filtration (usually an expensive synthetic filter) from early clogging. In the capture chambers of the Andreae Original filter, there is up to 5 times more paint captured than in standard fleece filters. The filter is equipped with a strap which prevents it from excessive stretching.

Delivery: size10 m2 x width 50, 75, 90 or 100 cm

![andrae-std.png](/uploads/andrae_std_160e170e04.png)

### Filter Andreae HC

In the type Andreae HC, there is a paper strip on the front side which partially overlaps the inlet holes. The effect is multiple: even capturing of paint overspray, reduction of pressure losses when filling the filters, capturing the oversprayed paint on the surface of the paper strip, higher holding capacity up to 10 – 40 %.

Delivery: size 8 m2 x width 50, 75, 90 or 100 cm

![andrae-hc.png](/uploads/andrae_hc_063550b9a9.png)

### Filter Andreae HE

This type of Andreae filter connects the advantages of an Andreae filter and a filter from synthetic fibres and thus it is regarded as two filters in one. The HE type has a layer of synthetic filter on the outlet side. In place of two filters enrolled in a row, two frames, double labour costs when swapping the filters and a larger inventory, it is possible to solve all this with Andreae HE filters.

Delivery: size 8 m2 x width 75, 90 and 100 cm

![andrae-he.png](/uploads/andrae_he_241ce9a440.png)

### Filter Andreae HP

Combines the advantages of HC (High Holding Capacity) type and HE (high efficiency) filter type. The filter has a paper strip glued on the front side and on the back a synthetic filter material. Andreae HP filter achieves very good results in the separation of overspray of paints at low costs of maintenance of spray booth.

Delivery: size 8 m2 x width 75, 90 or 100 cm

![andrae-hp.png](/uploads/andrae_hp_5b9b32de5a.png)

### Andreae Starter

![phpThumb_generated_thumbnail (11).jpeg](/uploads/php_Thumb_generated_thumbnail_11_75aedc31f5.jpeg)

Andreae Starter composed of two layers of sulphate cardboard. Layers are perforated, folded and glued together.

Holding capacity: up to 18 kg/m2*

Filtration efficiency: up to 98.1 %* 

Optimum conditions of use:

- Recommended air velocity: 0.25 - 1 m/s
- Pressure loss: 0.25 m/s - 8 Pa, 0.5 m/s - 20 Pa, 0.75 m/s - 30 Pa, 1 m/s - 40 Pa 
- Maximum recommended pressure loss: 128 Pa - 256 Pa 

Delivery: size 10 m2 x 100 or 75 cm

Paper filters Andreae

Andreae Starter

<ul><li>Disposable coat, without pockets and seams</li><li>Protection against chemical substances and dust particles</li><li>Microporous material</li><li>Colour: white</li><li>Use: as a protection against light sprays of liquid chemicals with low risk, dangerous solid particles, oils, resins and paints, protection during food processing</li><li>Intended for: paint shops, chemical, pharmaceutical, electrical engineering and mechanical engineering industries, agriculture and maintenance</li><li>EN13034/2005 type 6, EN13982/2004 type 5</li><li>Packing: 1 pc</li><li>Size: XL</li></ul>

medium_plast micromax ns.jpg

small_plast micromax ns.jpg

thumbnail_plast micromax ns.jpg

plast micromax ns.jpg

large_shutterstock_127981970_mensi.jpg

medium_shutterstock_127981970_mensi.jpg

small_shutterstock_127981970_mensi.jpg

thumbnail_shutterstock_127981970_mensi.jpg

shutterstock_127981970_mensi.jpg

<p style="margin-left:0px;">We offer a wide range of clothes for industrial paint shops, the automotive and chemical industry and also for other industrial fields.</p><p style="margin-left:0px;">We offer disposable coveralls and coats with protection level 5/6. Furthermore, we sell high-quality coveralls and coats for universal use and in various colours.</p><p style="margin-left:0px;">Clothes are delivered by first-class manufacturers of protective clothing such as 3M, Lakeland and HB Shutzbekleidung. The majority of clothes are antistatic.</p><h4 style="margin-left:0px;"><strong>Coat MicroMAX NS</strong></h4><figure class="image"><img src="https://admin.ewac.tech/uploads/php_Thumb_generated_thumbnail_9_2d1364e5ee.jpeg" alt="phpThumb_generated_thumbnail (9).jpeg"></figure><ul><li>Disposable coat, without pockets and seams</li><li>Protection against chemical substances and dust particles</li><li>Microporous material</li><li>Colour: white</li><li>Use: as a protection against light sprays of liquid chemicals with low risk, dangerous solid particles, oils, resins and paints, protection during food processing</li><li>Intended for: paint shops, chemical, pharmaceutical, electrical engineering and mechanical engineering industries, agriculture and maintenance</li><li>EN13034/2005 type 6, EN13982/2004 type 5</li><li>Packing: 1 pc</li><li>Size: XL</li></ul><h4 style="margin-left:0px;"><strong>Coat HABETEX MICRONSELECT</strong></h4><figure class="image"><img src="https://admin.ewac.tech/uploads/php_Thumb_generated_thumbnail_10_c2bfe9e152.jpeg" alt="phpThumb_generated_thumbnail (10).jpeg"></figure><ul><li>Product description: collar, front hem with hidden plastic zipper. 1 breast pocket left, 1 breast inner pocket right, 2 side pockets, raglan sleeve with plastic press studs for adjusting</li><li>Quality: HABETEX – Micronselect</li><li>Composition: 99 % polyester, 1 % carbon fibre</li><li>Weight: 115 g/m2</li><li>Size: 42/44 - 66/68</li><li>Colour: white</li><li>Intended for: automotive and industrial paint shops</li></ul><h4 style="margin-left:0px;"><strong>Overall MicroMAX NS</strong></h4><figure class="image"><img src="https://admin.ewac.tech/uploads/php_Thumb_generated_thumbnail_11_a2513fb549.jpeg" alt="phpThumb_generated_thumbnail (11).jpeg"></figure><ul><li>Lightweight disposable overall</li><li>Intended for protection against chemical spray, dust, liquids and water vapours</li><li>Antistatic properties</li><li>Other fabric properties: seams sealed with a tape; flap over the zipper is equipped with a two-sided adhesive tape to perfectly seal zippers; a three-part hood and embedded gusset in the crotch – the overall fits better and survives more</li><li>Complies with standards: EN 1149-1, EN 1073-2, EN 13034 type 6, EN 13982-1 type 5</li><li>Used also as protection against radioactive contamination particles</li><li>Colour: white</li><li>Size: M-3XL</li><li>Intended: for application in hospitals, in health-care, in clean rooms, in handling of chemical solutions, industrial maintenance, asbestos removal and handling of it, etc.</li></ul><h4 style="margin-left:0px;"><strong>Overall HABETEX MICRONPLUS (without hood)</strong></h4><figure class="image"><img src="https://admin.ewac.tech/uploads/KOMBINEZA_HABETEX_MICRONPLUS_2_barvy_bez_kapuci_1_fcfd581ba9.png" alt="KOMBINÉZA HABETEX MICRONPLUS 2 barvy, bez kapuci_1.png"></figure><ul><li>High quality: HABETEX – Micronplus</li><li>Composition: 99 % polyester, 1 % carbon fibre</li><li>Weight: 150 g/m2</li><li>Size: 42/44 to 66/68</li><li>Colours: two-colour version: royal blue/Bugatti blue or anthracite/silver grey, Single-color version – white and grey</li><li>Intended for: automotive and industrial paint shops</li></ul><h4 style="margin-left:0px;"><strong>Overall HABETEX MICRONSELECT (with hood)</strong></h4><figure class="image"><img src="https://admin.ewac.tech/uploads/php_Thumb_generated_thumbnail_12_1564e6ef9c.jpeg" alt="phpThumb_generated_thumbnail (12).jpeg"></figure><ul><li>High quality: HABETEX - Micronselect</li><li>Composition: 99 % polyester, 1 % carbon fibre</li><li>Weight: 115 g/m2</li><li>Size: 42/44 to 66/68</li><li>Colours: royal blue/anthracite/white</li><li>Intended for: automotive and industrial paint shops</li></ul><h3 style="margin-left:0px;"><strong>Overall Micromax CoolSuit</strong></h3><figure class="image"><img src="https://admin.ewac.tech/uploads/php_Thumb_generated_thumbnail_13_ab9a669257.jpeg" alt="phpThumb_generated_thumbnail (13).jpeg"></figure><ul><li>Disposable protection overall type 5 and 6</li><li>Protection against limited overspray and dust</li><li>Use: protection against paints and detergents and e.g. splashes of liquid chemicals with a low level of danger, various assembling works, paint shops, maintenance, etc.</li><li>Properties: a blue breathable part is inserted in the back area and this increases breathability</li><li>Breathable part on the back is made of Safegard 76 material in blue colour for easy identification. This part allows breathability of wear and this means that MicroMAX NS Cool Suit is comfortable even in the hottest working conditions</li><li>The suit contains blue connecting seams for excellent strength of the suit and also higher resistance against particles and liquids on seams</li><li>Colour: white with blue back and seams</li><li>Manufacturer: Lakeland</li><li>Size: M - 2XL</li><li>Packing: 1 pc</li></ul>

Protective clothes

Coat MicroMAX NS

<p>Filter media are manufactured from irregularly organized, by heat connected glass fibres. Flexible fibres in the medium are progressively thickened towards the side of clean air. This is smoothened or reinforced with a special layer. The progressive structure of media ensures good arrestance, high holding capacity for accumulation of rough particles, especially paint overspray and slow growth in pressure losses.&nbsp;</p><p>Due to the impregnation with a special binding agent, Paintstop Orange keeps high arrestance. Compared to the Paintstop Green, this filter is able to capture more dry particles.&nbsp;</p><h3>Field of use&nbsp;</h3><p>Paintstop Orange is used for capturing overspray in paint shops, especially where fast-drying lacquer or paint is used.&nbsp;</p><h3>Examples of use&nbsp;</h3><ul><li>Paint shops</li></ul><h3>Delivery:&nbsp;</h3><ul><li>Roll: 1x20 m; 2x20 m.</li><li>This filter can also be delivered in other dimensions.</li></ul>

small_Paintstop Yellow2.png

thumbnail_Paintstop Yellow2.png

Paintstop Yellow2.png

large_ewac_filtry_004.jpg

medium_ewac_filtry_004.jpg

small_ewac_filtry_004.jpg

thumbnail_ewac_filtry_004.jpg

ewac_filtry_004.jpg

### FLOOR FILTER/PAINT STOP

Filter media are manufactured from irregularly organized, by heat connected glass fibres. Flexible fibres in the medium are progressively thickened towards the side of clean air. This is smoothened or reinforced with a special layer. The progressive structure of media ensures good arrestance, high holding capacity for accumulation of rough particles, especially paint overspray and slow growth in pressure losses. 

### PAINTSTOP

![psw2.png](/uploads/psw2_4dea4897bb.png)

#### Field of use 

Filters from glass fibres are used as floor filtration material for separation of fine and tiny drops of paints. They can be used up to 120°C. 

#### Examples of use 

- Spraybooths 

#### Delivery
Rolls: 0.5 x 20 m; 0.6 x 20 m; 0.7 x 20 m; 0.75 x 20 m; 0.8 x 20 m; 0.9 x 20 m; 1 x 20 m; 1.3 x 20 m; 1.5 x 20 m; 2 x 20 m

### PAINTSTOP ORANGE

![resized_347x231_Paintstop Orange filter.png](/uploads/resized_347x231_Paintstop_Orange_filter_3c31035705.png)

Due to the impregnation with a special binding agent, Paintstop Orange keeps high arrestance. Compared to the Paintstop Green, this filter is able to capture more dry particles. 

#### Field of use
 
Paintstop Orange is used for capturing overspray in paint shops, especially where fast-drying lacquer or paint is used. 

#### Examples of use 

- Paint shops 

#### Delivery:

Roll: 1x20 m; 2x20 m

This filter can also be delivered in other dimensions. 
 
### MATIC 4‘, MATIC 5' 

![matic. transparent.png](/uploads/matic_transparent_e04dc11419.png)

Unwinding filters Matic are used as prefilters for systems with multi-level filtration. The filter medium is produced from irregularly laid, heat connected glass fibres with high arrestance due to the impregnation with a special binding agent and it is able to capture more dry dust particles.

#### Field of use

Industrial paint shops

#### Example of use

- Ventilation system of the paint shop (AAF, CEAG, Dürr, etc.) 

#### Standard size

MATIC 4: 1,141 x 20 m

MATIC 5: 1,446 x 20 m

Paintstop filters

PAINTSTOP ORANGE

<p>Filter media are manufactured from irregularly organized, by heat connected glass fibres. Flexible fibres in the medium are progressively thickened towards the side of clean air. This is smoothened or reinforced with a special layer. The progressive structure of media ensures good arrestance, high holding capacity for accumulation of rough particles, especially paint overspray and slow growth in pressure losses.&nbsp;</p><h3>Field of use</h3><p>Filters from glass fibres are used as floor filtration material for separation of fine and tiny drops of paints. They can be used up to 120°C.&nbsp;</p><h3>Examples of use&nbsp;</h3><ul><li>Spraybooths</li></ul><h3>Delivery&nbsp;</h3><p><strong>Rolls:&nbsp;</strong></p><ul><li>0.5 x 20 m;</li><li>0.6 x 20 m;</li><li>0.7 x 20 m;</li><li>0.75 x 20 m;</li><li>0.8 x 20 m;</li><li>0.9 x 20 m;</li><li>1 x 20 m;</li><li>1.3 x 20 m;</li><li>1.5 x 20 m;</li><li>2 x 20 m</li></ul>

PAINTSTOP

<p>In paint shops with dry and wet filtration, we use the GrayWolf GW 3016 Channel Particle Counter to measure particle concentration. The instrument displays data on cumulative and differential particle counts. A protocol with recorded values ​​is issued from each measurement.</p><p>Specifications:</p><p>Size range: 0.3 – 10.0 μm</p><p>Flow: 0.1 CFM (2.83 LPM)</p><p>Concentration limits: 4,000,000 particles / ft3</p><p>at 5% n.z.1 1Accidental loss</p>

large_motiv4_1801x1164px.jpg

medium_motiv4_1801x1164px.jpg

small_motiv4_1801x1164px.jpg

thumbnail_motiv4_1801x1164px.jpg

motiv4_1801x1164px.jpg

large_shutterstock_155301083_mensi.jpg

medium_shutterstock_155301083_mensi.jpg

small_shutterstock_155301083_mensi.jpg

thumbnail_shutterstock_155301083_mensi.jpg

shutterstock_155301083_mensi.jpg

<p>EWAC® Filter management brings many benefits to customers. Starting with always ensuring timely deliveries of filters, through the assessment of the effectiveness of deployed filters to reduce costs in the form of analysis of filtration systems, measurements and design leading to the efficiency of the filtration system.</p><p>Thanks to EWAC® Filter management, the customer has more information about his filter system, so he can decide on the necessary adjustments or changes in the functioning of individual components to ensure optimal air flow, prevent waste caused by inappropriate flow or air pollution.</p><p>EWAC® Filter management provides our partners in various industries with the maximum benefit from our high-quality filters installed in complex operations.</p><p>EWAC® Filter management includes a wide portfolio of high-quality air filters with low pressure loss and high dust particle capture, which will help you reduce costs even for electrical energy.</p><p>&nbsp;</p>

Filter management

MEASUREMENT OF DUST IN PAINT SHOPS

<ul><li>Woven rag</li><li>Intended for: treatment of especially plastic surfaces before painting</li><li>Smooth, white rag with light impregnation</li><li>Size: 50 x 20 cm</li><li>Packing: 50 pc</li></ul>

small_ewac_06_19_5.png

thumbnail_ewac_06_19_5.png

ewac_06_19_5.png

TAKrag 1079 (D3035)

<p>We ensure the measurement of climatic and air-technical parameters using the Testo 440 device, which will determine the air quality in the room, including air temperature and pressure. Based on the identified parameters, we will develop a suitable solution for you.</p><p>A protocol with recorded values ​​is issued from each measurement.</p><p>We ensure the measurement of climatic and air-technical parameters using the Testo 440 device, which will determine the air quality in the room, including air temperature and pressure. Based on the identified parameters, we will develop a suitable solution for you.</p><p>A protocol with recorded values ​​is issued from each measurement.</p><p><strong>Specifications:</strong></p><p><strong>Glow wire probe</strong></p><p>Measuring range: 0 – 20 m/s</p><p>Accuracy: ±( 0.03 + 4% of n.h.2)</p><p>Temperature: -20 …… +70 °C</p><p><strong>Propeller probe with a diameter of 100 mm</strong></p><p>Measuring range: 0.1 – 15 m/s</p><p>Accuracy: ± (0.1 m/s + 1.5% of n.h.3)</p><p>Temperature: -20 …… +70 °C</p><p>2Measured value</p><p>3Measured value</p>

large_motiv3_1801x1164px.jpg

medium_motiv3_1801x1164px.jpg

small_motiv3_1801x1164px.jpg

thumbnail_motiv3_1801x1164px.jpg

motiv3_1801x1164px.jpg

FALL RATE MEASUREMENT 

<ul><li>One-sided adhesive PE foil with acrylic adhesive</li><li>For protection of walls, windows and TL-luminairs against paint overspray</li><li>Also for protection of work tables in paint mixing rooms</li><li>Removable without glue residue up to 6 months</li><li>Resistant against water, mechanical damage, chemical influences and heat-proof up to 60 °C</li><li>Thickness: 30 and 50 µ</li><li>Dimension: 0.25, 0.50 and 1.00 x 100 m</li><li>Size: 0,5 and 1,0 x 100 m</li></ul>

large_Krycí fólie čirá ewac_15_33_bile pozadi.jpg

medium_Krycí fólie čirá ewac_15_33_bile pozadi.jpg

small_Krycí fólie čirá ewac_15_33_bile pozadi.jpg

thumbnail_Krycí fólie čirá ewac_15_33_bile pozadi.jpg

Krycí fólie čirá ewac_15_33_bile pozadi.jpg

large_shutterstock_231167821_mensi.jpg

medium_shutterstock_231167821_mensi.jpg

small_shutterstock_231167821_mensi.jpg

thumbnail_shutterstock_231167821_mensi.jpg

shutterstock_231167821_mensi.jpg

We offer various types of tacky foils and non-tacky foils for floors, doors, desks, walls, windows and lamps. Tacky foils contain adhesive and they are used for protection of surfaces in paint shops against their pollution and damage during painting. Foils are easily removable and do not leave residues of adhesives on the surface.

Non-tacky cover foils for cars are made of polyethylene and protect cars and their parts against pollution and work as a protection against overspray.

Tacky mat is an anti-dust mat which allows capturing of dust or impurities and thus significantly reduces the possibility of bringing impurities to clean rooms. By walking over the mat, dust and impurities from shoes are captured. 

Covering papers protect floors against pollution and overspray. 

#### Floor paper

![Protection board floor.png](/uploads/Protection_board_floor_6b33ea1140.png)

- Temporary protection of floors of spray booths against impurities, coloured overspray and dust
- Flexible cardboard with white top side
- Equipped with PE foil on both sides
- Can be fixed by using a universal tape or Delta Duct Extra tape
- Roll width: 130 cm
- Length: 1 roll: 50 m²
- Thickness: 0,45 mm
- Packing: 1 pc
 
#### Tacky foil TRANSPARENT

![ewac_15_33.png](/uploads/ewac_15_33_aec9778a83.png)

- One-sided adhesive PE foil with acrylic adhesive
- For protection of walls, windows and TL-luminairs against paint overspray
- Also for protection of work tables in paint mixing rooms
- Removable without glue residue up to 6 months
- Resistant against water, mechanical damage, chemical influences and heat-proof up to 60 °C
- Thickness: 30 and 50 µ
- Dimension: 0.25, 0.50 and 1.00 x 100 m
- Size: 0,5 and 1,0 x 100 m 
  
#### Dust mats

![phpThumb_generated_thumbnail (1).jpeg](/uploads/php_Thumb_generated_thumbnail_1_2bfc419b24.jpeg)

- Tacky anti-dust mat allowing capture of dust or dirt and significantly reducing the possibility of bringing impurities into clean rooms
- By walking across the mat, dust and dirt from shoes remain on it
- Packing: 1 mat

Types of mats:

- Blue mat 30/60 layer. Size: 115 x 45 or 115 x 60 or 115 x 90 cm
- White mat 30/60 layer. Size: 115 x 45 or 115 x 60 or 115 x 90 cm
- Grey mat 30/60 layer. Size: 115 x 45 or 115 x 60 or 115 x 90 cm 

#### Black-and-white floor covering foil

![ewac_14_30.png](/uploads/ewac_14_30_6c9ae69676.png)

- Black-and-white foil, tacky from the bottom side
- Polyethylene foil protecting floors against contamination and damage
- easy to remove without adhesive residues
- UV-resistance: 12 months
- Thickness: 80 μm (microns)
- Roll size: 0.5 x 250 m


Cover foils and papers, dust mats

Tacky foil TRANSPARENT

<ul><li>Water-based coating</li><li>Used for wall protection against overspray</li><li>Easy application with a roller, brush or spray gun</li><li>Usable up to 85°C</li><li>Temporary protection of walls, windows, lamps against overspray in spray booths</li><li>Reduces dust rate in the spray booth</li><li>Easily washed down with warm water</li></ul>

small_Ochrnanný nástřik_mensi2.png

thumbnail_Ochrnanný nástřik_mensi2.png

Ochrnanný nástřik_mensi2.png

TACKY coating

<p>In the type Andreae HC, there is a paper strip on the front side which partially overlaps the inlet holes. The effect is multiple: even capturing of paint overspray, reduction of pressure losses when filling the filters, capturing the oversprayed paint on the surface of the paper strip, higher holding capacity up to 10 – 40 %.&nbsp;</p><p><strong>Delivery:</strong> size 8 m<sup>2</sup> x width 50, 75, 90 or 100 cm.</p>

small_3. Andreae High Efficiency Filter.png

thumbnail_3. Andreae High Efficiency Filter.png

3. Andreae High Efficiency Filter.png

Filter Andreae HC

<p>This set of equipment is intended for the washing of spray guns and parts contaminated with water-diluted paints.&nbsp;</p><p>After the washing of parts on the washing desk, the contaminated water is recharged by using a submersible pump, located in the washing desk, into the sedimentation device EWACLEAN 200, where the cleaning process is carried out using powdery reaction products.&nbsp;</p><p>After the process of sludge filtration in the draining containers, water can be released into the sewerage system or it can be reused in the washing process.&nbsp;</p><p><strong>Device performance</strong>: 200 - 400 litres/1 hour.</p><p><i>(*) - Performance of the device is dependent on the level of pollution of the waste water</i></p><p><i>(**) - Weight of the device is shown without the medium.</i></p>

large_EWACLEAN 200 a MYCI STUL.jpg

medium_EWACLEAN 200 a MYCI STUL.jpg

small_EWACLEAN 200 a MYCI STUL.jpg

thumbnail_EWACLEAN 200 a MYCI STUL.jpg

EWACLEAN 200 a MYCI STUL.jpg

large_EWACLEAN 200_komplet.jpg

medium_EWACLEAN 200_komplet.jpg

small_EWACLEAN 200_komplet.jpg

thumbnail_EWACLEAN 200_komplet.jpg

EWACLEAN 200_komplet.jpg

EWAC spol. s r.o. started production of sedimentation devices EWACLEAN and RCA in 2012. These devices are intended for cleaning of rinsing and waste waters containing stains, adhesives, waterborne paints, emulsions and dispersions.

Technological devices are manufactured from PP and PVC. 

### Sedimentation device EWACLEAN 100

![phpThumb_generated_thumbnail.jpeg](/uploads/php_Thumb_generated_thumbnail_49aae614ff.jpeg)

A compact device intended for cleaning of rinsing and waste waters containing waterborne paints, emulsions and adhesives.

The device works in semi-automated operation.

Performance: approx. 100 – 200 litres / 1 hour.

The device is designed for operations with a small production of waste waters.

#### Function of the device

1st Cleaning phase

Rinse water is pumped into the reactive part of the device. The process of mixing is initiated on the control panel. This causes homogenization of pumped waste water.

2nd Cleaning phase

During mixing, the relevant quantity of proposed reactive product is dosed manually. The mixing process automatically ends after about 10-15 minutes and the sedimentation process starts.

3rd Cleaning phase

After the end of sedimentation (approx. 10 minutes), the draining ball valve PVC DN 50 mm is opened. The entire volume of the reactive part is released through the draining boxes with a filtration bag. Cleaned water is automatically pumped to the sewerage system. The captured sludge is thoroughly drained in the filtration bag after about 30 minutes.

### Sedimentation device EWACLEAN 200

![phpThumb_generated_thumbnail (1).jpeg](/uploads/php_Thumb_generated_thumbnail_1_ddc987934b.jpeg)

A compact device intended for cleaning of rinsing and waste waters containing waterborne paints, emulsions and adhesives.

This device works in semi-automatic operation.

Performance: approx. 200 – 400 litres / 1 hour.

The device is designed for operations with small and medium production of waste waters.

#### Function of the device

1st Cleaning phase

Rinsing water is pumped into the reactive part of the device. The process of mixing is initiated on the control panel. This causes homogenization of pumped waste water.

2nd Cleaning phase

During mixing, the relevant quantity of proposed reactive product is dosed manually. The mixing process automatically ends after about 10-15 minutes and the sedimentation process starts.

3rd Cleaning phase

After the end of sedimentation (approx. 10 minutes), the draining ball valve PVC DN 50 mm is opened. The entire volume of the reactive part is released through the draining boxes with a filtration bag. Cleaned water is automatically pumped by a submersible pump to the sewerage system. The captured sludge in the filtration bag is thoroughly drained after about 30 minutes.

### Sedimentation device EWACLEAN 200 with washing table

![phpThumb_generated_thumbnail (2).jpeg](/uploads/php_Thumb_generated_thumbnail_2_ed4da6b861.jpeg)

This set of equipment is intended for the washing of spray guns and parts contaminated with water-diluted paints.

After the washing of parts on the washing desk, the contaminated water is recharged by using a submersible pump, located in the washing desk, into the sedimentation device EWACLEAN 200, where the cleaning process is carried out using powdery reaction products. 

After the process of sludge filtration in the draining containers, water can be released into the sewerage system or it can be reused in the washing process.

Device performance: 200 - 400 litres/1 hour.

Sedimentation device EWACLEAN

Sedimentation device EWACLEAN 200 with washing table

<ul><li>Nonwoven rags</li><li>Slightly impregnated</li><li>Material: polyamide and polyester</li><li>For easy degreasing of all surfaces</li><li>Fast drying</li><li>Size: 32 x 40 cm</li><li>Packing: 25 pc</li></ul>

small_ewac_07_21_5.png

thumbnail_ewac_07_21_5.png

ewac_07_21_5.png

IPA wipes 500

<p>Special filtration papers made of cellulose or glass submicron fibres with the required filter class are used as a filtration medium.&nbsp;</p><p>This filtration paper is folded into the required filter class. This filter paper is folded into a stable thread with the optimal number of folds and height with respect to the operating point of the filter. Hot-melt beads ensure not only stability of a compact fold structure, but also regular and parallel folds of the filtration medium and this allows a complete use of the filter area. Filter thread is sealed by sealant into the filter frame made of MDF board (pressed wooden fibres), equipped with a protective layer.&nbsp;</p><p>If the humidity-stable filter is required, it is possible to use a water-resistant plywood. On request, the frame can be made of the following materials –zinc-plated steel metal sheet, stainless steel metal sheet or aluminium metal sheet. Flat rubber sealing is standardly glued onto the inner side of the filter insert.&nbsp;</p><h3>Field of use</h3><p>Filter inserts MULTIPLAN in filter classes F6, F7 and F9 are used especially as prefilters for highly efficient filter inserts, for which they ensure the appropriate conditions of their function and prolonged lifespan. The economical dimensions of filter inserts allow their mutual installation into filtration cabinets.&nbsp;</p><h3>Advantages of design</h3><ul><li>Proved structure ensures high mechanical stability</li><li>High flexibility in use</li><li>High nominal air flow rate in small dimensions</li><li>Separation of filtration paper without the use of metals</li><li>Filter area is optimized according to the use</li></ul><h3>Examples of use&nbsp;</h3><p>As prefilters in industries</p><ul><li>Medicine - Microbiology</li><li>Chemical industry</li><li>Pharmaceutical industry</li><li>Food-processing</li><li>Electrical engineering industry</li></ul><h3>Delivery&nbsp;</h3><p>Filter inserts, various sizes.</p>

thumbnail_multiplan-0_2.png

multiplan-0_2.png

large_ewac_filtry_003.jpg

medium_ewac_filtry_003.jpg

small_ewac_filtry_003.jpg

thumbnail_ewac_filtry_003.jpg

ewac_filtry_003.jpg

### Filterzelle-Glass (FZ-G) 

FZ-G filter consists of a paper frame and a medium made of glass fibres, so-called Paintstop. Filtration glass medium has a progressive structure, meaning it thickens towards the outlet side of the filter. The result is a higher holding capacity of dust particles.

Moreover, the medium is impregnated with an adhesive substance, increasing accumulation of rough dust particles at very low pressure loss. Glass medium is fixed to the cardboard frame. 

![fz-g.png](/uploads/fz_g_88a69d8a3b.png)

#### Field of use

- Paint shops
- Filtration of rough dust particles

#### Delivered sizes

497 x 497 x 45 mm
597 x 597 x 45 mm
497 x 624 x 45 mm 

### FILTER INSERTS Z-LINE

![zline-0.png](/uploads/zline_0_74701d27ae.png)

Filter inserts Z-line consist of folded synthetic filtration fleece which is inserted into the stable frame, impregnated against humidity, made of cardboard with a protective grille on the inlet or outlet side.

Z-shape folded filtration medium allows high air flow at low pressure loss and small installation depth. Filtration medium is reinforced with a net and cannot regenerate.

Standard building depths are 48mm, 96mm, 147mm. At the customer request, we can deliver depth from 25 to 150 mm.

#### Field of use

Filter inserts of Z-line are used for rougher filtration in ventilation and air-conditioning equipment. 

#### Advantages of design

- High economic efficiency due to low initial pressure drop and high nominal airflow rate
- After use, filters can be completely burnt
- High active filtration area ensures high dust holding ability
- Air supply equipment
- General ventilation and air-conditioning
- Prefilters of air inlet for clean area
- Automotive industry
- Paint shops

#### Examples of use

- Air supply equipment
- General ventilation and air-conditioning
- Prefilters of air inlet for clean area
- Automotive industry
- Paint shops

### FILTER INSERTS MULTIPLAN

![multiplan-0_2.png](/uploads/multiplan_0_2_b3b414d4cd.png)

Special filtration papers made of cellulose or glass submicron fibres with the required filter class are used as a filtration medium.

This filtration paper is folded into the required filter class. This filter paper is folded into a stable thread with the optimal number of folds and height with respect to the operating point of the filter. Hot-melt beads ensure not only stability of a compact fold structure, but also regular and parallel folds of the filtration medium and this allows a complete use of the filter area. Filter thread is sealed by sealant into the filter frame made of MDF board (pressed wooden fibres), equipped with a protective layer.

If the humidity-stable filter is required, it is possible to use a water-resistant plywood. On request, the frame can be made of the following materials –zinc-plated steel metal sheet, stainless steel metal sheet or aluminium metal sheet. Flat rubber sealing is standardly glued onto the inner side of the filter insert.

#### Field of use

Filter inserts MULTIPLAN in filter classes F6, F7 and F9 are used especially as prefilters for highly efficient filter inserts, for which they ensure the appropriate conditions of their function and prolonged lifespan. The economical dimensions of filter inserts allow their mutual installation into filtration cabinets.

#### Advantages of design

- Proved structure ensures high mechanical stability
- High flexibility in use 
- High nominal air flow rate in small dimensions  
- Separation of filtration paper without the use of metals 
- Filter area is optimized according to the use

#### Examples of use

As prefilters in industries

- Medicine
- Microbiology 
- Chemical industry 
- Pharmaceutical industry
- Food-processing 
- Electrical engineering industry 

#### Delivery

Filter inserts, various sizes 

Filter cells

FILTER INSERTS MULTIPLAN

<p>The base of the filter insert is the filtration medium in the form of special filtration papers made of glass sub-micron fibres.&nbsp;</p><p>This filtration paper is folded into a stable folded thread, whose optimal number and height of folds is in compliance with the operating point of the filter and ensures the required filter class and long lifespan of the filter insert. The paper is separated by hot melt (MACROPUR) beads or with separators made from aluminium foil (MACROPUR).&nbsp;</p><p>Filter thread is hermetically sealed into a stable, torsion-resistant filter frame and along with endless sealing from PUR foam it guarantees a high-quality sealing of the filter insert in the mounting cabinets. This filter structure is the base for compliance with high requirements for air purity. The basic frame is made of MDF. On request, it is also possible to make the filter frame from zinc-plated, stainless or aluminium metal sheets.&nbsp;</p><h3>Field of use</h3><ul><li>Medicine</li><li>Microbiology</li><li>Chemical industry</li><li>Pharmaceutical industry</li><li>Food-processing industry</li><li>Electrical engineering industry</li><li>Nuclear technology</li></ul><h3>Examples of use&nbsp;</h3><p>This highly efficient filter insert with high arrestance of all types of aerosols is used as the end filter of multi-level filtration in air-conditioning and ventilation equipment, for purifying of inlets and outlets of air in technologically demanding processes and purification of air from health-harmful dust, viruses, and bacteria in hospital facilities.&nbsp;</p><h3>Advantages of design&nbsp;</h3><ul><li>High mechanical stability</li><li>Optimal structure of the thread</li><li>Steady output airflow velocity</li><li>Various types of frame and sealing</li></ul><h3>Delivery&nbsp;</h3><ul><li>Filter inserts, various sizes.</li><li>Paper separation: hot-melt beads, aluminium foil.</li></ul>

MACROPUR 

large_EWACLEAN 200_bez beden.jpg

medium_EWACLEAN 200_bez beden.jpg

small_EWACLEAN 200_bez beden.jpg

thumbnail_EWACLEAN 200_bez beden.jpg

EWACLEAN 200_bez beden.jpg

large_AC 200-02_m.JPG

medium_AC 200-02_m.JPG

small_AC 200-02_m.JPG

thumbnail_AC 200-02_m.JPG

AC 200-02_m.JPG

<p>A compact device intended for cleaning of rinsing and waste waters containing waterborne paints, emulsions and adhesives.&nbsp;</p><p>This device works in semi-automatic operation.&nbsp;</p><p><strong>Performance</strong>: approx. 200 – 400 litres / 1 hour.&nbsp;</p><p>The device is designed for operations with small and medium production of waste waters.&nbsp;</p><h3>Function of the device</h3><h4>1st Cleaning phase&nbsp;</h4><p>Rinsing water is pumped into the reactive part of the device. The process of mixing is initiated on the control panel. This causes homogenization of pumped waste water.&nbsp;</p><h4>2nd Cleaning phase&nbsp;</h4><p>During mixing, the relevant quantity of proposed reactive product is dosed manually. The mixing process automatically ends after about 10-15 minutes and the sedimentation process starts.&nbsp;</p><h4>3rd Cleaning phase&nbsp;</h4><p>After the end of sedimentation (approx. 10 minutes), the draining ball valve PVC DN 50 mm is opened. The entire volume of the reactive part is released through the draining boxes with a filtration bag. Cleaned water is automatically pumped by a submersible pump to the sewerage system. The captured sludge in the filtration bag is thoroughly drained after about 30 minutes.</p><p><i>(*) - Performance of the device is dependent on the level of pollution of the waste water</i></p><p><i>(**) - Weight of the device is shown without the medium.</i></p>

Sedimentation device EWACLEAN 200

large_EWACLEAN 100_bez beden.jpg

medium_EWACLEAN 100_bez beden.jpg

small_EWACLEAN 100_bez beden.jpg

thumbnail_EWACLEAN 100_bez beden.jpg

EWACLEAN 100_bez beden.jpg

large_AC 100-02_m.JPG

medium_AC 100-02_m.JPG

small_AC 100-02_m.JPG

thumbnail_AC 100-02_m.JPG

AC 100-02_m.JPG

<p>A compact device intended for cleaning of rinsing and waste waters containing waterborne paints, emulsions and adhesives.&nbsp;</p><p>The device works in semi-automated operation.&nbsp;</p><p><strong>Performance:</strong> approx. 100 – 200 litres / 1 hour.&nbsp;</p><p>The device is designed for operations with a small production of waste waters.&nbsp;</p><h3>Function of the device&nbsp;</h3><h4>1st Cleaning phase&nbsp;</h4><p>Rinse water is pumped into the reactive part of the device. The process of mixing is initiated on the control panel. This causes homogenization of pumped waste water.&nbsp;</p><h4>2nd Cleaning phase&nbsp;</h4><p>During mixing, the relevant quantity of proposed reactive product is dosed manually. The mixing process automatically ends after about 10-15 minutes and the sedimentation process starts.&nbsp;</p><h4>3rd Cleaning phase&nbsp;</h4><p>After the end of sedimentation (approx. 10 minutes), the draining ball valve PVC DN 50 mm is opened. The entire volume of the reactive part is released through the draining boxes with a filtration bag. Cleaned water is automatically pumped to the sewerage system. The captured sludge is thoroughly drained in the filtration bag after about 30 minutes.</p><p><i>(*) - Performance of the device is dependent on the level of pollution of the waste water</i></p><p><i>(**) - Weight of the device is shown without the medium.</i></p>

large_EWACLEAN 100_komplet.jpg

medium_EWACLEAN 100_komplet.jpg

small_EWACLEAN 100_komplet.jpg

thumbnail_EWACLEAN 100_komplet.jpg

EWACLEAN 100_komplet.jpg

Sedimentation device EWACLEAN 100

<p>Both types consist of five paper layers. The filter CI-Eurosupra I (CI-ES I) has the sixth layer on the outlet side made of a fine synthetic filter fabric.&nbsp;</p><p>Filter CI-Eurosupra II (CI-ES II) has this layer made of a rougher material.&nbsp;</p><h3>Filter is especially suitable for use with&nbsp;</h3><ul><li>Epoxide paints</li><li>Waterborne paints</li><li>PU paints</li><li>Top paints</li><li>Primers</li><li>Stains</li><li>Air-drying paints</li><li>Base paints</li></ul><h3>Packing&nbsp;</h3><ul><li>Roll 1.06 x 10 m</li></ul>

large_Columbus filtr.jpg

medium_Columbus filtr.jpg

small_Columbus filtr.jpg

thumbnail_Columbus filtr.jpg

Columbus filtr.jpg

The Columbus filter consists of several layers of specially perforated paper overlapping one another and they provide a large capturing area. Openings of one layer are organized opposite the previous layer. In circulating air, turbulence is caused and this results in catching of solid particles on individual layers of the filter.

Moreover, each layer of the filtration paper has a different structure. The openings are gradually smaller and smaller and upper layers get clogged more slowly than the bottom ones. This causes a regular load on all paper layers and the filter gets clogged equally in its entire depth. This all contributes to the high holding capacity and long lifespan of the filter.

Where high efficiency of filtration is required, it is necessary to use Eurosupra filters. Several layers of filtration paper on the outlet side are complemented by a layer of synthetic filter medium of different structures. 

#### Field of use 

Columbus filters are intended for separation of overspray of paints and lacquers in dry spray booths and paint shops. With respect to the fact that filters have a high holding capacity and a very good efficiency, it is possible to use them for practically the majority of liquid paints, e.g. base, waterborne, top, bake-dry, polyurethane, primers, stains, epoxides, glues, etc. 

### CI – STANDART

Filter CI-Standard (CI-S) consists of six perforated paper layers.
Each layer has a different size of openings, from the biggest to the smallest. 

![ci-s-1.png](/uploads/ci_s_1_4298e2c34f.png)

#### Filter is especially suitable for use with 

- Primers
- Air-drying paints
- Stains
- Nitrocellulose paints
- Base paints
- Waterborne paints 

#### Packing

Roll 1.06 x 12 m

### CI – EUROSUPRA I A II

Both types consist of five paper layers. The filter CI-Eurosupra I (CI-ES I) has the sixth layer on the outlet side made of a fine synthetic filter fabric.

Filter CI-Eurosupra II (CI-ES II) has this layer made of a rougher material. 

![ci-e-1_1.png](/uploads/ci_e_1_1_4117cdefba.png)

#### Filter is especially suitable for use with

- Epoxide paints
- Waterborne paints
- PU paints
- Top paints
- Primers
- Stains
- Air-drying paints
- Base paints

#### Packing
Roll 1.06 x 10 m

### CI – HIGH CAPACITY

The filter CI-High Capacity (CI-HC) consists of eight layers of perforated paper with a different structure.

Three inlet layers have extremely large openings. The filter has a high paint holding capacity. 

![ci-h-cap-1.png](/uploads/ci_h_cap_1_855c650d08.png)

#### Filter is especially suitable for use with

- Glues
- Polyurethane paints
- Base paints
- Air-drying paints
- Epoxides
- Stains

#### Packing

Roll 1.06 x 10 m

### CI – HC EUROSUPRA

The filter CI-High Capacity Eurosupra (CI-HCS) combines the advantages of the filter CI-HC and Eurosupra II.

It consists of seven paper layers with a various size of openings and from one layer of a synthetic material which is on the outlet side of the filter. 

![ci-h-eur-1.png](/uploads/ci_h_eur_1_6342c55fda.png)

#### Filter is especially suitable for use with

- Epoxide paints
- Waterborne paints
- PU paints
- Top paints
- Primers
- Glues
- Air-drying paints
- Base paints

#### Packing

Roll 1.06 x 10 m

### INSTALLATION KIT COLUMBUS
  
The installation kit is intended for attaching Columbus filters.

Kit contains: grille, hook, and lid. 

![resized_150x169_mrizka.png](/uploads/resized_150x169_mrizka_c53aa217b3.png)
![phpThumb_generated_thumbnail (18).jpeg](/uploads/php_Thumb_generated_thumbnail_18_68a6528903.jpeg)
![resized_150x147_vicko.png](/uploads/resized_150x147_vicko_e0ebe304a7.png)


Paper filters Columbus

CI – EUROSUPRA I A II

+420 385 344 740

PAINTSTOP ORANGE

PAINTSTOP ORANGE

Field of use

Examples of use

Delivery:

Related Products

Peelable coating white AZ1 – 700

ULTRAPUR

Cleaning rag Cleanbez 08

Andreae Starter

Painstop Orange		DSW 2"	DSW 4“
Thickness	[mm]	50	100
Initial pressure drop	[Pa]	10 - 40	15-55
End pressure drop	[Pa]	130	130
Arrestance A	[%]	95 - 98	98
Holding capacity	[kg/m2]	4.5 – 5.9	4.5-6.5
Max. operating temperature	[°C]	65	65
Medium		glass fibre